The lithium Battery Protection Board is the charge and discharge protection for the series-connected lithium battery pack; when fully charged, it can ensure that the voltage difference between the individual cells is less than the set value (generally ±20mV), so as to realize the equal charge of each single cell of the battery pack. , effectively improving the charging effect in the series charging mode; at the same time, it detects the overvoltage, undervoltage, overcurrent, short circuit, and overtemperature status of each single cell in the battery pack to protect and prolong the battery life; undervoltage protection makes each A single-cell battery is used to avoid damage to the battery due to overdischarge. Lithium Iron Battery,Lithium Iron Battery Board,Industrial Control Board,Medical PCBA Board,Circuit Board Assembly Huizhou Liandajin Electronic Co., Ltd , https://www.ldjpcb.com
Lynx Box 1 Generation How ROOT
How Lynx box generation ROOT, this does not have a fixed answer, because there are different ways for different versions of the built-in ROM version, before the 1.6 version, ROOT method is relatively simple, just get the box, just a ROOT master can ROOT out of the box, but later version update, it is invalid, to 1.6 version to the extreme, because Ali built anti-ROOT code in boot.img, even if you ROOT, a restart will fail, so after 1.6 The version ROOT method is not the same as before. I think that if there is a box now, whether it is just taken or used for some time, it is unlikely that there will be an old version of ROM, so we will do it for the 1.7 ROM. A newly effective ROOT method set after the ROOT 1.6, the preferred Flash short-circuit method, this method is suitable for the latest generation of the latest generation of the ROM box is appropriate, because Android starts with a flash chip containing bootloader code, if you start After taking this Flash, the system will think Bootloader is lost, will look for the boot file on the TF card first, so that we can use RECOVERY on the TF card to brush into the cracked version Boot.img and third-party RECOVERY, so that it will work. Another option is the TTL method. You need to buy a small TTL board, install the necessary driver, disassemble, and tripartite RECOVERY:
Use this latest version directly
If you are upgrading from the previous ROM, and has already replaced the third party RECOVERY, then you can single brush the latest version of the ROOT package clean, OTA automatic upgrade, ROOT will fail, can only be brushed once into the RECOVERY, if Want to enter RECOVERY to operate, you can enter via REBOOT RECOVERY in the system, which is more convenient
2. Replace BOOT.img after ROOT
Unpack BOOT.IMG, in the init.rc, delete the ROOT PROTECT code 
After completing the above steps, you can access the third party RECOVERY, you do not need to short-circuit, no more TTL, you need to find the ROM you want and brush into it. There are several other versions, and More optional, because the other manufacturers of ROM is not deep customization, so the maximum to retain the characteristics of Android itself, such as setting the interface, and Tmall is replaced by its own interface, I am not very used to use!
4. Prevent Alibaba Cloud from automatically upgrading
Ali system, from the initial release to the latest 1.7, I feel that the upgrade does not bring any substantial benefits, but based on the outflow ROOT method to block, so when you brush the Alibaba Cloud system and complete the above steps, you can Check whether the OTA has been removed, otherwise the story will not necessarily happen after the automatic upgrade. The above steps are enough to enjoy the method of preventing the upgrade and delete the OTA procedure. Change the DNS method.
The above methods are the latest and most effective methods. Most of them have been tested. If they fail, please specify that I will modify the posts! Recently, there has been very little tossing of the box generation. After all, the box generation is relatively old, and there are many new boxes in the hands.
Recommendation: What are the changes in Lynx Box 1 and 1s?
[playing machine skills] Lynx Box 1 generation how ROOT
What is ROOT for? The ultimate goal is still to be able to replace the third-party ROM and provide more functions, so to achieve this goal, you first need to use a third party RECOVERY, because the built-in official RECOVERY is to verify the digital certificate of the brush pack, and Ali's Digital certificate, you can not get, so if you replace the RECOVERY for the third party, you will not verify the certificate, you can freely refresh, in order to exchange RECOVERY, you need to brush into the third party RECOVERY, this It is a function that requires ROOT permission, so this is why we must first ROOT and then brush RECOVERY and then change the ROM! First of all, you need to replace the BOOT first, otherwise it will fail to restart BOOT.ING when you restart after ROOT. 3. Replace ROM
As I mentioned at the beginning, because Ali built ROOT code in BOOT.IMG, so ROOT