The key problem of LED road lighting degradation is temperature. LED street lights are usually lost in this link. Since the LED street lamp has higher luminous power than the household lamp, the manufacturer has painstakingly designed the heat sink substrate fin and the heat dissipation module. The assembly needs to be outside the lamp heat dissipation module, and the paint is protected to prevent weather erosion. Unexpectedly, this externally protected spray paint sealed the heat of the heat-dissipating module, resulting in poor heat dissipation and LED epitaxial light decay. LED epitaxial luminescence heat energy belongs to a small range of concentrated heat energy. In the application of high-power street lamps, the power input power is also large, and the interface temperature of the LED is quite high. If the street lamp continues to work for a long time, if the heat dissipation module cannot effectively dissipate heat, Will affect the LED life and luminescence performance, such as the current LED street lights severe light decay is caused by these factors. LED street lights are used outdoors and have environmental and environmental interference factors. Therefore, most manufacturers use the anode treatment of LED street light radiators or spray paint to avoid acid and alkali corrosion. The life of the anode treatment is not long, and it will oxidize and discolor for a long time. If you want to remove the heavy work, not only the time and labor will increase the maintenance cost; the paint protection cost is lower, the protection effect is good, but the general paint does not dissipate heat. Function, the paint body itself will form a barrier function, which is equivalent to increase the thermal impedance of the LED street light radiator, which not only does not help, but because the heat energy is blocked in the heat sink, the LED light power is reduced, and finally the serious light decay is caused. The above has been seriously plagued by the LED lighting industry, and it is almost the main reason why the public works LED street lights cannot pass the procurement unit's acceptance. LED road light failure solution recommendations: To solve these existing problems, it is recommended that street lamp manufacturers start with basic materials and solve the problem of high-power LED heat sources from the inside out. For example, when the light-emitting component is bonded to the aluminum substrate, the thermal conductive adhesive plays a key role. Some manufacturers think that the thermal conductivity film or the thermal conductive rubber pad has a good thermal conductivity, and the thicker the film thickness, the better, but does not want the thermal resistance problem. The thermal conductivity is good, and the thermal resistance of the film thickness is useless. Moreover, the thermal conductive film or the soft thermal conductive gasket does not really adhere to the substrate, and there are actually many voids in the bonding surface. These pores are viewed under an electron microscope, like a hollow cavitation, another form of thermal resistance. In the presence of so many thermal resistances that interfere with heat conduction, the efficiency of heat and heat conduction is virtually reduced. To use the thermal ceramic adhesive, the recommended soft ceramic thermal adhesive. The soft ceramic thermal conductive adhesive of screen printing is different from the traditional laminated thermal conductive adhesive film. The soft ceramic thermal conductive adhesive is soft semi-liquid. When the screen printing machine blade is coated on the aluminum substrate, the thermal conductive particles will penetrate into the pores of the substrate surface and Fill it up to full. This results in a completely flat, non-porous plane that will completely conform to the LED epitaxial carrier. In this way, the thermal resistance is minimized, and the heat can be quickly conducted, which naturally reduces the ambient temperature of the LED die, and also prolongs the life of the epitaxial crystal and greatly delays the occurrence of light decay. In addition, due to the ductility of the soft ceramic thermal conductive paint applied by screen printing, it will change with the thermal expansion and contraction of the aluminum substrate during high temperature baking or reflow, the stress is very small, and the aluminum substrate will not be bent, nor will it be caused. Will burst. In the external protection of LED lamps, LED lamps and soft ceramic heat-dissipating paints are recommended. The spray-type soft ceramic heat-dissipating paint can be directly sprayed on the outside of the LED lamp, and the construction operation is simple, and can be adapted to various shapes of heat-dissipating structures, and can also be adjusted to different colors, in response to the needs of landscape design. The soft ceramic particles in the spray-type heat-dissipating paint are subjected to nano-treatment, and the fine particles are not only easy to be sprayed, but also the heat-conducting particles on the same coating area are dense and dense, and the area of ​​temperature volatilization is also increased. Let the heat of the LED luminaire be quickly conducted out. Soft ceramic heat-dissipating paint is a thermosetting material that conforms to RoHS environmental protection safety regulations. The construction procedure is simple and does not require any special equipment. After baking, it is heat-set, and it can withstand the high temperature of LED for a long time without quality change. LED street lights, landscape lights, or LED advertising billboards used outdoors will also face acid and alkali damage such as wind and rain, acid rain, bird droppings, air dust, and black smoke emission hELlip. Therefore, this spray-type soft ceramic heat-dissipating paint must have the characteristics of acid and alkali resistance. The current acid-base resistance range is PH3~11, which can effectively protect the appearance of LED outdoor lamps from being eroded. The cost structure of LED lamps has been continuously improved with the development of packaging technology, carrier board design and heat dissipation module structure, and the cost has also decreased with the development of technology and market demand. However, there are not many manufacturers investing in material improvement, which is mainly related to the history and habits of Taiwan's industrial and commercial development. Taiwanese manufacturers are more prone to process and design, and have less ink on material development. Therefore, in the issue of solving technical problems or reducing costs, it is more biased towards purchasing thinking or management thinking. However, at the first time, US and Japanese manufacturers will think about the application materials, reduce costs, improve quality and increase profits from the perspective of innovation.
There is a rule, custom laptop is called programming laptop cause nearly 90% is used for projects. 15.6 inch laptop for coding and programming is usually equipped with 10th or 11th cpu, 2gb or 4gb graphics optional. 15 inch laptop untuk programming is used on big tender or group for a special jobs. 15.6 inch programming laptop under 30000 is a more competitive one for business or high school students or teachers.
However, here is the recommended laptop for programming, especially for heavy office jobs or university coursework, since double heat-releasing, metal body, bigger battery, FHD screen, high-level cpu, etc. Build the deep and stable foundation to enjoy smooth running experience. Your clients will satisfy it`s excellent performance. Of course, there are other lower specification with tight budget.
As a entry windows laptop for programming, this 14 inch celeron Education Laptop is the most competitive and hottest device for elementary project.
Any other special requirements, just contact us freely.
Programming Laptop,Laptop For Coding And Programming,Programming Laptop Under 30000,Recommended Laptop For Programming,Windows Laptop For Programming Henan Shuyi Electronics Co., Ltd. , https://www.shuyilaptops.com