introduction The popularization of cars has brought convenience to people's lives, and it also poses a big problem for people-car theft prevention. This design is to solve the shortcomings and deficiencies of the previous car anti-theft products and developed an integrated car anti-theft alarm system that integrates three major functional modules of sensing, alarm and remote image monitoring. System working principle and composition This system is to install the sensor in the hidden position of the body. When someone walks into the monitoring distance, the body moves or vibrates, and the door is opened, the sensor sends an electrical signal to the main controller through the A / D conversion device. According to the source of the signal, the controller divides the alarm into three levels: "someone is approaching", "car body vibration" and "the door is opened", and uses GPRS / GSM terminal to send the alarm information to the user's mobile phone by SMS. Take "door opened" as a high-level alarm, notify the user, start the video driver, record the live situation in the car through the camera in the car, and send it to the owner's mobile phone. In the first two cases, the system does not transmit images unless the client actively views the images. At this time, the system hardly occupies the channel. When an intruder enters the defense area, the MCU sends a warning message to the user via SMS. Because only text messages are sent at this time, the amount of information is small, and the speed of information transmission is fast. At the same time, the system stores the screen at the time of alarm in the storage device in the system for the user to view. The overall framework of the system hardware design system The system hardware consists of the following modules: main controller module, information acquisition module (sensor), USB camera module, wireless communication module (GPRS MODEM) and image compression module. Main control module Samsung's S3C2410 is based on the ARM core, the maximum operating frequency can reach 203MHz, can support NAND flash memory startup, and has a higher cost performance. In addition, S3C2410 has many mature applications in the market, so S3C2410 was selected as the system CPU. The S3C2410 integrates an LCD controller (supports STN and TFT liquid crystal display), NAND flash memory controller, SDRAM controller, 3 channel UART, 4 channel DMA, 4 timers with PWM function and 1 internal Clock, and 8-channel 10-bit ADC. S3C2410 also has a lot of rich external interfaces, such as touch screen, I2C bus, 12S bus interface, and 2 US host interfaces, 1 USB device interface, 2 SPI interfaces, SD interface. In terms of clock, S3C2410 integrates an RTC (Real Time Control) with calendar function and a chip clock generator with PLL. Can produce an operating frequency of 200MHz. This working frequency can make the processor easily run WinCE, Linux and other operating systems, as well as more complex data processing. USB camera The USB camera is mainly composed of 3 parts: lens, image sensor and USB interface control chip. The camera used in this system is a relatively common one on the market. Its USB interface control chip model is 301p, the image sensor chip uses CMOS technology, so the cost performance is higher. The camera can directly communicate with the host through the USB interface, and transfer the collected images to the host. The characteristics of the chip are as follows: the maximum image is 640 & TImes; 480 pixels, which can be configured and adjusted according to different cameras; the image white balance and other parameters can be configured; it can be efficiently operated under the Arm-Linux embedded system; the internal CMOS image sensor is programmed through the I2C bus Register to change the default parameters. Wireless communication module This system uses the GSM2406 module. It has a simple interface and is easy to use. It only needs a single 2.7V power supply to work. The AT command is used to control this module, and the initial plan is to use a serial port to communicate with the controller. At the same time, use this module to realize the voice call function. Since GPRS is based on the IP protocol, the processor must send data packets that conform to the IP protocol when communicating with the GPRS network. Image compression module Because the video processing chip 1s outputs 25 frames of images, and a frame of 640 & TImes; 480 images is about 2.45Mb, in order to ease the storage pressure of the memory, the images must be compressed to increase the access speed. The system design uses the ZR36060 image compression chip with integrated JPEG codec. It can easily realize real-time compression / decompression of video signals. When compressing, ZR36060 receives YUV 4: 2: 2 digital video signal and encodes it as JPEG stream output; when decompressing, it receives JPEG stream and decodes it as YUV 4: 2: 2 digital video signal Output. The interface of ZR36060 is divided into 3 parts, namely video interface, code and host interface and control interface. The function of the video interface is to complete the input / output of the video signal; the function of the code and host interface is to complete the initialization of the chip control word through the host, and in the active mode, the JPEG compressed code stream also passes CODE [7: 0] input / output ; The control interface completes a series of simple work sequence control operations. The two video synchronization methods are sync master mode and sync slave mode. Synchronous master mode means that all control and timing signals are generated inside the chip; synchronous slave mode means that the chip is used as a slave to synchronize with an external video source. Data acquisition module The data collection module of the anti-theft system consists of a microwave Doppler sensor group, a vibration sensor group, a Hall device group, and a pyroelectric infrared sensor group. It is used for the collection of automobile anti-theft information and the preliminary fusion processing of data. The structure of the data acquisition module is shown in Figure 1. Figure 1 The composition of the data acquisition module Using microwave Doppler sensors to monitor the intrusion range The microwave Doppler sensor uses HB100 microwave motion sensor module of Agilis. HB100's Doppler effect transceiver module uses dielectric resonance oscillator and microstrip patch antenna technology to achieve low current consumption, high temperature stability and high sensitivity. Use acceleration sensor to monitor vehicle body vibration and tilt By measuring the vibration and tilt of the car body, it is possible to give early warning to the phenomenon that the thief uses the towing method to steal the vehicle and damage the car body. Because the acceleration sensor ADXL202E can measure the dynamic or static acceleration in the range of 0 ~ 5kHz, ± 2g: the measurement of dynamic acceleration can be used for vibration detection, and the static gravity acceleration can be used as the input vector to determine the spatial direction of the object. Therefore, ADXL202E can be used to monitor the vibration and tilt angle of the car body at the same time. Use Hall switch device to monitor the switch of car door A3210E is a Hall effect switching device. Using digital signal output, the Hall effect can be produced under the action of the north and south magnetic poles: when the magnetic pole is close, the switch is turned on, and the output level is low; when the magnetic pole is far away, the switch is turned off, and the output level is high. The power consumption of this type of sensor is very low. For example, the power consumption of A3209E is as low as 400mW, which is especially suitable for low power consumption applications. The design of the Hall device group is to distribute multiple Hall devices to the four doors of the car. When the door is opened, the Hall device will emit a weak electrical signal, and then send the output signal of each switching device to the device group. The local decision center is integrated. Here, the alarm levels of the four doors are considered to be the same, and the hardware can be used to directly OR After calculation, the fusion result is sent to the central processing module. Thunderbolt 3 Cable Shenzhen GuanChen Electronics Co., Ltd. , https://www.gcneotech.com